Finlux 55F9076-T Bedienungsanleitung PDF herunterladen (Seite 18)

English - 17 -

ConguringWiredNetworkSettingsin

Advanced Mode

After pressing the GREEN button, the “Advanced

mode” will be available. While in Advanced Mode,

press the REDbuttontoeditsettings.Whennished,

press OK to save, Press RETURN/BACK to cancel.

Wireless Connectivity

To Connect to a Wireless Network

IMPORTANT: “Veezy 200” USB dongle is required to

use wireless network features.

•To make your modem’s SSID visible, you should

change your SSID settings via the modem’s

software. The TV cannot connect to the networks

with a hidden SSID.

To Connect to a wireless LAN, you should perform

the following steps:

1. Ensure that Nero Media Home software is

installed to your PC (for DLNA function).

2. Then connect the wireless adaptor to one of the

USB inputs of the TV.

3. Tocongureyourwirelesssettingspleaserefer

to the Network settings section in this manual.

Broadband

ISP

connection

Wireless LAN

adaptor

USB inputs

rear left side

of the TV

•A Wireless-N router (IEEE 802.11a/b/g/n) with

simultaneous 2.4 and 5 GHz bands is designed

to increase bandwidth. These are optimized for

smoother and faster HD video streaming, file

transfers and wireless gaming.

•Use a LAN connection for quicker file sharing

between other devices like computers.

• The frequency and channel differ depending on the area.

•The transmission speed differs depending on the

distance and number of obstructions between the

transmission products, the conguration of these

products,theradiowaveconditions,thelinetrafc

and the products that you use. The transmission may

also be cut off or may get disconnected depending

on the radio wave conditions, DECT phones or any

other WiFi 11b appliances. The standard values of

the transmission speed are the theoretical maximum

values for the wireless standards. They are not the

actual speeds of data transmission.

• The location where the transmission is most effective

differs depending on the usage environment.

•The Wireless LAN adaptor should be connected directly

to the TV’s USB port. USB hubs are not supported. You

canplugyourwidongleintothesupplieddockIn

cases where network quality is poor and the wi

dongle needs to be placed to a location with better

signal quality.

•The WirelessLANadaptor supports802.11a,b,g&

n type modems. It is highly recommended that you

should use the IEEE 802.11n communication protocol

in order to avoid any possible problems while watching

videos.

• Use the other USB input, if you experience problems

with audio/video performance.

• You must change your modem’s SSID when there are

any other modems around with the same SSID. You

can encounter connection problems otherwise. Use

a wired connection if you experience problems with a

wireless connection.

ConguringWirelessDeviceSettings

To enable Wi-Fi features, plug in the Wi-Fi dongle to

one of the USB ports. Open the Network Settings menu

and select Network Type as Wireless Device to start

connection process.

Press the YELLOW button to scan the wireless

networks. A list of available networks will be displayed.

Please select your desired network from the list.

Note: If the modem supports N mode, you should set

N mode settings.

If the selected network is protected with a password,

please enter the correct key by using the virtual

keyboard. You can use this keyboard via the navigation

buttons and the OK button on the remote control.

Wait until the IP address is shown on the screen.

This means that the connection is now established. To

disconnect from a wireless network press OK.

You can navigate between menu tabs by pressing left/

right buttons. The help bar on the bottom of the dialog

shows features that you may use. Press the BLUE

button to check your internet connection speed. Press

the GREEN button to switch to advanced mode and

then press the OK button to edit settings.

You can check the signal strenght by using the network

settings menu for the wireless device mode.

Other Information

Configuration Status: Displays Wi-Fi status as

connected or not connected.

IP Address: Displays the current IP address.

1 2 ... 13 14 15 16 17 18 19 20 21 22 23 ... 32 33

Kommentare zu diesen Handbüchern

Keine Kommentare

Finlux 55F9076-T Bedienungsanleitung Seite 18

Kommentare zu diesen Handbüchern

Verwandte Produkte und Handbücher für LCD-Fernseher Finlux 55F9076-T